Home › Oil and Gas Services › Free Oilfield Calculators

Oil & Gas · Free tools

Free Oilfield Calculators

Ten calculators for the math that comes up on location every day. They run in your browser, send nothing anywhere and work on a phone. Example values are filled in; type over them and the answers update as you go.

By Robert Adam Clifford, Lost Cabin Consulting LLC · Updated October 25, 2026

Field aid only. These calculators use standard oilfield formulas and round their answers. They are free, with no guarantee of accuracy, and are not engineering advice or a substitute for the well plan, company procedures or a qualified engineer's review. Check every number before it goes into a job. See the Disclaimer.

Well control

Hydrostatic pressure

The pressure a column of fluid puts on bottom, from the fluid weight and the true vertical depth.

ppg
ft
Hydrostatic pressure–psi

Gradient–psi/ft

Per 1,000 ft–psi

Specific gravity–SG

Formula and notes

Hydrostatic pressure (psi) = 0.052 × fluid weight (ppg) × TVD (ft). Gradient (psi/ft) = 0.052 × ppg. Use true vertical depth, not measured depth.

Well control

Kill weight fluid

The fluid weight that balances formation pressure, from the shut-in drillpipe or tubing pressure.

ppg
psi
ft
Kill weight–ppg

Rounded up to 0.1–ppg

Formation pressure–psi

Kill fluid gradient–psi/ft

Formula and notes

Kill weight (ppg) = original weight + SIDPP ÷ (0.052 × TVD). Formation pressure (psi) = SIDPP + 0.052 × original weight × TVD. No trip or safety margin is added; follow the well control plan.

Volumes

Pipe and annular capacity

The volume inside a string and in the annulus around it. Set the pipe OD to 0 for open casing or open hole.

in
in
in
ft
Total circulating volume–bbl

Pipe volume–bbl

Pipe capacity–bbl/ft

Annular volume–bbl

Annular capacity–bbl/ft

Formula and notes

Capacity (bbl/ft) = ID² ÷ 1029.4. Annular capacity (bbl/ft) = (casing ID or hole² − pipe OD²) ÷ 1029.4. Volume = capacity × length. Total = pipe volume + annular volume.

Volumes

Pipe displacement

How much fluid a string moves going in the hole, open-ended or plugged. Use it to check the trip tank and returns.

in
in
ft
Open-end displacement–bbl

Open-end–bbl/ft

Closed-end displacement–bbl

Closed-end–bbl/ft

Formula and notes

Open-end (steel) displacement (bbl/ft) = (OD² − ID²) ÷ 1029.4. Closed-end displacement (bbl/ft) = OD² ÷ 1029.4. Couplings and upsets add a little more.

Hydraulics

Annular velocity and bottoms up

How fast returns travel up the annulus at a pump rate, and how long bottoms up takes.

bbl/min
in
in
ft
Annular velocity–ft/min

Bottoms up–min

Bottoms-up volume–bbl

Pump rate–gpm

Formula and notes

Annular velocity (ft/min) = rate (bbl/min) ÷ annular capacity (bbl/ft). Bottoms up (min) = annular volume (bbl) ÷ rate (bbl/min). 1 bbl/min = 42 gpm.

Tubulars

Buoyed string weight

What a string weighs hanging in fluid, for comparing to the weight indicator.

lb/ft
ft
ppg
Buoyed weight–lb

Weight in air–lb

Buoyancy factor–

Formula and notes

Buoyancy factor = (65.4 − fluid weight in ppg) ÷ 65.4, for steel. Buoyed weight = weight in air × length × buoyancy factor. Blocks, drag and deviation are not included.

Fishing

Free point from stretch

Estimate how much pipe is free above the stuck point from the stretch measured under a differential pull.

in
in
in
lb
Free pipe to about–ft

Pipe wall area–in²

Stretch constant–in per 1,000 lb per 1,000 ft

Free point constant–

Formula and notes

Free pipe (ft) = 2,500,000 × stretch (in) × wall area (in²) ÷ differential pull (lb), for steel, with wall area = 0.7854 × (OD² − ID²). This is the same as Wild Well Control's 1.9635 × stretch × (OD² − ID²) ÷ pull in thousands of pounds. Pull over string weight, mark the pipe, pull again and measure between the marks. Friction and deviation make the real free point deeper than the estimate; confirm with a free-point tool before cutting or backing off.

Snubbing

Snubbing force and balance point

The force needed to snub pipe into a well under pressure, and the depth where the string goes from pipe light to pipe heavy.

psi
lb
in
in
in
lb/ft
ppg
ppg
ft
Balance point, pipe empty–ft

Snub force, pipe body in the seal–lb

Snub force, coupling in the seal–lb

Balance point, pipe filled–ft

At the pipe in the hole (empty)–

Formula and notes

Snub force (lb) = wellhead pressure × 0.7854 × OD² + friction, using the largest OD in the sealing element. Weight of empty pipe in the well (lb/ft) = nominal weight − 0.0408 × well fluid ppg × OD²; filling the pipe adds 0.0408 × fill fluid ppg × ID². Balance point (ft) = snub force (pipe body) ÷ that weight. Above the balance point the string is pipe light and must be snubbed; below it the string is pipe heavy and can be stripped. These follow Wild Well Control and Grace's Advanced Blowout and Well Control; check them against the snubbing contractor's job calculations.

Rod lift

Rod pump displacement

Theoretical and expected output of a rod pump from plunger size, stroke length and strokes per minute.

in
in
SPM
%
Expected output–bbl/day

Theoretical output–bbl/day

Plunger constant–K

Fluid load constant–lb/ft

Formula and notes

Output (bbl/day) = 0.1166 × plunger diameter² × stroke (in) × SPM. Expected = theoretical × efficiency. Fluid load constant = 0.340 × diameter² (lb per foot of net lift at SG 1.0).

Units

Unit conversions

Type in either box and the other one updates.

bbl
gal
bbl
m³
bbl
ft³
psi
kPa
psi
bar
ft
m
in
mm
lb
kg
ppg
SG
ppg
kg/m³
ppg
lb/ft³
°F
°C
Notes

SG uses 8.33 ppg for fresh water, the usual oilfield figure. °C = (°F − 32) ÷ 1.8.

Background

Where the numbers come from

0.052 converts pounds per gallon to psi per foot (12 in/ft ÷ 231 in³/gal), 1029.4 turns inches squared into barrels per foot, and 65.4 ppg is the weight of steel. The formulas match Wild Well Control's Technical Data Book, Grace's Advanced Blowout and Well Control and the service company tech books. Pipe sizes, IDs, drifts and capacities for common tubing and casing, sucker rod and plunger data, and fluid gradients are in the oilfield tech references. For cleanout volumes and rates in more depth, see Tag Bottom; for the consultant's side of the job, The Chair.

Need a hand on location?

Adam has more than 24 years in completions, workover and fishing. Reach him by email or LinkedIn.

Email Adam LinkedIn